Enlarge

Pedestrian LED Traffic Signal Options
(Meets 1999 ITE Specifications)

Features

• 2-Row, 9" high countdown digits are MUTCD compliant for crosswalks over 100 ft.
• Full preemption compatibility - Reverts to its previous timing immediately following a preemption call.
• Unique memory feature allows countdown time to remain stored internally, even when power is removed for extended periods of time.
• Up to 4 units can be connected in parallel without disturbing the monitoring of the Hand/Person.
• Automatically adjusts to traffic controller interval changes.
• 90% reduction in power vs. incandescent.
• Long life: up to 10 times longer than incandescent.
• Sealed moisture resistant enclosure.
• Lens available to fit most pedestrian heads.
• Lens has a textured surface to reduce glare.
• Easy to install into existing signal enclosure.

Specifications

• Operating Voltage Range: 80VAC to 135 VAC (120V nominal)
• Fuse and transient suppressor incorporated for line and load protection
• Operating Temperature Range -40°C to +74°C
• Meets FCC Title 47, Subpart B, Section 15 Regulations for electrical noise
• Provided with quick connect terminals and spade adapters
• LED Colors:
  Countdown Numerals - Portland Orange
  Hand - Portland Orange
  Walking Person - Lunar White

TYPICAL OPERATING CHARACTERISTICS

Pedestrian LED Traffic Signal Options
(Meets 2005 ITE Specifications)

Lighting Uniformity • ITE Conformity

Features / Benefits

• Uniform non-pixelated appearance
• Exceeds ITE PTCSI Part 2 requirements for LED pedestrian signals
• Fuse and transient suppressor incorporated for superior line and load protection
• 90% reduction in power vs. incandescent
• Long life: up to 10 times longer than incandescent
• Sealed moisture resistant enclosure
• Lens has a textured surface to reduce glare
• Easy to install into existing signal enclosure

Specifications

• Operating Voltage Range: 80VAC TO 135 VAC (120VAC nominal)
• Operating Temperature Range: -40°C to +74°C
• Meets FCC Title 47, Subpart B, Section 15 regulations for electrical noise
• Failed State Impedance > 250K ohm within 300 ms
• Conforms to MIL-STD-810F for blowing rain
• Conforms to MIL-STD-883, Test Method 2007, for mechanical vibration
• Conforms to MIL-STD-883, Test Method 1010, temperature cycling requirements
• Provided with quick connect terminals and spade adapters
• All products traceable by serial number
• Symbol Colors:
  • Upraised Hand - Portland Orange
  • Walking Person - Lunar White
• Transient Suppression exceeds ITE PTCSI-2 LED Pedestrian Signal Specification requirements and meets the following standards:
  • NEMA TS-2 Sec. 2.1.6 and Sec. 2.1.8
  • IEC 1000-4-5, 3KV, 2 ohm source impedance
  • ANSI/IEEE C62, 41-2002; IEC 61000-4-12, 6KV, 200A, 100KHz ring wave
• Power supply is conformally coated for robust operation

Pedestrian LED Signal Options
(Meets 2005 ITE Specifications)
Lighting Uniformity • ITE Conformity

Features / Benefits

• Uniform appearance symbols exceed ITE PCSI-2 requirements
• 9" high, 2-row countdown digits for maximum visibility
• Countdown is fully MUTCD-compliant (even for crosswalks over 100 ft.)
• Unique memory feature allows countdown time to remain stored internally, even when power is removed for extended periods of time
• Full preemption compatibility. Countdown reverts to its previous timing immediately following a preemption call
• Up to 4 units can be connected in parallel without disturbing the monitoring of the Hand/Person
• Automatically adjusts to traffic controller interval changes
• 90% reduction in power vs. incandescent
• Long life; up to 10 times longer than incandescent
• Sealed moisture resistant enclosure
• Lens has a textured surface to reduce glare
• Easy to install into existing signal enclosure

Specifications

• Operating Voltage Range: 80VAC TO 135 VAC (120VAC nominal)
• Operating Temperature Range: -40°C to +74°C
• Turn-on/Turn-off time < 75 msec
• Power Factor > 0.9
• Total Harmonic distortion < 20%
• Meets FCC Title 47, Subpart B, Section 15 regulations for electrical noise
• Conforms to MIL-STD-810F for blowing rain
• Conforms to MIL-STD-883, Test Method 2007, for mechanical vibration
• Conforms to MIL-STD-883, Test Method 1010, temperature cycling requirements
• Provided with quick connect terminals and spade adapters
• Written manufacturer’s warranty available on request
• All products traceable by serial number
• Luminance uniformity and color uniformity exceed ITE PTCSI-2 LED Pedestrian Signal Specification requirements
• Transient Suppression exceeds ITE PTCSI-2 LED Pedestrian Signal Specification requirements and meets the following standards:
• NEMA TS-2 Sec. 2.1.6 and Sec. 2.1.8
• IEC 1000-4-5, 3KV, 2 ohm source impedance
• ANSI/IEEE C62, 41-2002; IEC 61000-4-12, 6KV, 200A, 100KHz ring wave.

TYPICAL OPERATING CHARACTERISTICS